防静电自流平基面处理案例

发布日期:2019-06-24 浏览次数:5

环氧防静电自流平地坪被称之为车间防静电地坪,其成膜丰富,固含量高,具有超强的耐压、耐磨性能,而且硬度好,耐刮伤,面层具有很好的耐磨性,持久耐用。适用于通讯设备制造厂、精密电子制造厂、计算机房、医院手术室、及有防静电要求的场所。因为一些高科技型电子企业,它对于地坪性能有着极高的要求,除了耐压耐磨耐冲击之外还要具备防静电功能。那么环氧防静电地坪对于基面有怎样的要求呢?主要有以下四点要求:

Epoxy anti-static self-leveling floor is called workshop anti-static floor. It has rich film, high solid content, super pressure and wear resistance, good hardness, scratch resistance, good wear resistance and durability. It is suitable for communication equipment manufacturers, precision electronics manufacturers, computer rooms, hospital operating rooms, and places with anti-static requirements. Because some high-tech electronic enterprises, it has very high requirements for floor performance, in addition to pressure, wear and impact resistance, but also has anti-static function. So what are the requirements of epoxy anti-static floor for the base surface? There are four main requirements: 第一点:基层打磨与清理

First point: grass-roots grinding and cleaning

施工前,一定要区分开施工区域,首先将地面各种垃圾清理干净,包括表层积水、油污、旧漆膜等等,然后进行打磨,确保地面平整。如果地面有凹凸不平的地方,可以用手磨机或是砂纸进行局部打磨。

Before the construction, we must distinguish the construction area, first clean up all kinds of rubbish on the ground, including surface water, oil, old paint film, etc., and then grind to ensure the smooth surface. If the ground is rough, you can use a hand grinder or sandpaper for local grinding.

为了增强与树脂之间的结合力,需将水泥基面打毛,最后使用吸尘器清理,清理后的地面要保持封闭状态。

In order to enhance the bonding force with the resin, the cement base surface needs to be groomed, and finally cleaned with a vacuum cleaner. After cleaning, the ground should be kept closed.第二点:地坪的固砂与修补

Second point: sand consolidation and repair of floor

如果地面存在细小裂缝,建议你先使用环氧树脂进行修补,然后再进行自流平的施工。

If there are small cracks in the ground, it is recommended that you use epoxy resin to repair them first, and then carry out self-leveling construction.第三点:地坪基面要求

Third point: Floor base requirements

对于防静电环氧自流平地坪来说,它要求地面强度在C20以上,使用2m靠尺检查时要求偏差小于2mm,而且表面不能有任何油污等污物。

For the anti-static epoxy self-leveling floor, it requires that the ground strength should be above C20, the deviation should be less than 2mm when checking with 2m ruler, and there should be no oil contamination on the surface.第四点:表面含水率要求

Fourth point: surface moisture requirement

因为防静电环氧自流平对于表面的含水率有严格要求,所以施工前要进行含水率测定,含水率不能超过8%,如果地面含水率超标的话,就要采用喷灯烘干,喷灯也就是喷火灯。

Because anti-static epoxy self-leveling has strict requirements for surface moisture content, water content should be measured before construction. Water content can not exceed 8%. If the surface moisture content exceeds the standard, it is necessary to use a spray lamp to dry, that is, a spray lamp.

辛苦整理!转载请注明来自 http://pengs888.com/show.asp?id=127

你觉得这篇文章怎么样?

0 0
网友评论

管理员

该内容暂无评论

美国网友
在线咨询
微信咨询
联系电话
137-7148-9633
返回顶部