您的位置:首页 > 工程案例

水性环氧地坪施工案例

发布日期:2019-06-27 浏览次数:6

“无规矩不成方圆”,世上的事情呢大抵都是如此。对于工程来说什么才是它们的规矩?是流程。关于水性环氧地坪的施工流程,你又知道多少呢?我们首先要把施工所需的工具准备好,以免在施工过程中慌乱。在施工过程中主要用到的工具有:地板打磨机、搅拌机、刷子、吸尘机械、刮刀或者是锯齿状镘刀还有消泡辊子等。工具准备好后就开始施工了。到这里,水性环氧地坪的施工就完成了。但是在施工完成之后的24小时,可以穿软底鞋进入,48小时之后才能够正常使用。并且一周内不能接触水、油、碱酸、硅等化学物。上述的问题虽小但一定要注意,否则会给后期的使用造成不必要的麻烦。

"No rules, no circles." This is almost the same thing in the world. What are their rules for engineering? They are processes. How much do you know about the construction process of waterborne epoxy floor? First of all, we should prepare the tools needed for construction, so as to avoid panic in the construction process. In the construction process, the main tools used are: floor grinder, mixer, brush, vacuum cleaner, scraper or serrated trowel, defoaming rollers and so on. When the tools are ready, construction begins. Here, the construction of waterborne epoxy floor is completed. But 24 hours after the completion of the construction, you can wear soft soles to enter, 48 hours before normal use. And within a week can not contact water, oil, alkaline acid, silicon and other chemicals. Although the above problems are small, we must pay attention to them, otherwise they will cause unnecessary trouble for later use.第一步:环氧底涂施工

First step: epoxy primer construction

将水性底涂固化剂与水性底漆主剂按重量比3:1进行混合,混合后用电动搅拌机搅拌均匀,然后按1:1的比例加水进行调配,充分搅拌均匀,之后采用滚涂或者喷涂进行涂装。

The water-borne primer curing agent and the main agent of the water-borne primer are mixed at a weight ratio of 3:1. After mixing, they are evenly stirred by an electric mixer. Then water is added at a ratio of 1:1 to mix them well and evenly. Then they are coated by rolling or spraying.

水性环氧混合好的材料最好在40分钟内使用完,涂装时涂装时要做到薄而均,涂布后表面有光泽,没有光泽的地方在适当的时候要进行补涂。等到水性底涂干了之后就可以进行中涂层的施工了。

Water-borne epoxy mixed material is best used in 40 minutes. When painting, it should be thin and uniform. After coating, the surface is glossy. Where there is no gloss, it should be repaired at the appropriate time. When the water-based base coating is dry, the construction of the intermediate coating can be carried out. 

第二步:中涂砂浆层施工

Step 2: Construction of Middle-coated Mortar Layer

先把水性中涂固化剂和水性环氧中涂主剂按重量比3:1进行混合,用电动搅拌机搅拌均匀,然后加入30%-40%的水充分搅拌,再加入适量的石英砂进行搅拌。

Firstly, water-borne curing agent and water-borne epoxy main agent were mixed at a weight ratio of 3:1, and evenly stirred by electric mixer. Then, 30% - 40% water was added to mix fully, and then a proper amount of quartz sand was added to mix.

在这些都完成后将得到的材料倒在地上用镘刀进行批涂,批涂时尽量避免刀痕的出现。材料最好在30分钟内用完。等到中涂层砂浆层干燥以后,就可以进行中涂腻子层的施工。

After these are completed, the obtained materials are poured onto the ground and batched with a trowel to avoid the occurrence of knife marks. Material should be used up in 30 minutes. After the middle coated mortar layer is dried, the middle coated putty layer can be constructed.

第三步:中涂腻子层施工

Step 3: Construction of Middle-coated Putty Layer

这一步的施工和中涂砂浆层的施工是一样的。

The construction of this step is the same as that of medium-coated mortar layer.

等到涂腻子层干燥后,用磨光机进行打磨,使地面平整光滑。打磨好之后,要记得用扫把或者吸尘器最少清理两遍。

Wait until the putty layer is dried and polished with a polisher to smooth the ground. After polishing, remember to clean it at least twice with a broom or vacuum cleaner

第四步:面漆施工

Step 4: Topcoat construction

先将水性环氧面漆固化剂和水性环氧面漆主剂按重量比4:1进行混合,进行搅拌,之后再加入20%的水进行搅拌。

The curing agent of waterborne epoxy topcoat and the main agent of waterborne epoxy topcoat were mixed at a weight ratio of 4:1 to stir, then 20% water was added to stir.

搅拌之后,用刮涂的方式进行施工,等到地面干燥后再用滚涂或喷涂的方式进施工。

After mixing, the construction is carried out by scraping, and after the ground is dried, the construction is carried out by rolling or spraying.

辛苦整理!转载请注明来自 http://pengs888.com/show.asp?id=154

你觉得这篇文章怎么样?

0 0
网友评论

管理员

该内容暂无评论

美国网友
在线咨询
微信咨询
联系电话
137-7148-9633
返回顶部